A “pass” on the home inspection doesn’t mean the HVAC system is healthy
You got the inspection report back. The furnace and AC are listed under “functional at time of inspection” with no red flags. That sounds like good news, and an agent will often tell you it is. But in Delaware County, where so much of the housing stock is pre-1960s with additions, converted systems, and decades of DIY patchwork, “functional at time of inspection” means something much narrower than most buyers assume. It means the system turned on when the inspector flipped the thermostat. It does not mean the compressor is charged correctly, the heat exchanger is safe, or the furnace will make it through another winter.
This gap is where post-closing HVAC disputes come from. A buyer moves in, runs the AC for the first time in June, and discovers it blows warm. Or the furnace trips out on its first cold night and a technician finds a cracked heat exchanger that should have failed a safety test years ago. The general inspector didn’t miss anything they were required to catch. They just weren’t testing for it.
What a standard home inspector actually checks (and what they skip)
General home inspectors in Pennsylvania typically follow ASHI-style Standards of Practice, which define HVAC scope narrowly. Under those standards, an inspector is expected to:
- Visually inspect the furnace, air handler, and condenser from the outside
- Operate the system using normal controls, usually the thermostat, to confirm it turns on and responds
- Note the energy source and describe the general type of system
- Flag obvious visual defects like rust, corrosion, or missing covers
What’s explicitly outside that scope, and what most inspectors are neither trained nor equipped to do, is the diagnostic work that actually reveals whether a system is near failure:
- Pulling access panels to inspect the heat exchanger or coil directly
- Measuring refrigerant charge against the system’s rated pressures
- Checking electrical amp draw against the compressor or blower motor’s nameplate specs
- Running a combustion analysis or CO test on a gas furnace
- Measuring static pressure in the ductwork to see if the system is straining to breathe
None of that is a knock on general inspectors. It’s not their job, and most are upfront about it if you ask directly. But if nobody asks, buyers walk into closing assuming “the home inspector checked the HVAC” covers all of it. It doesn’t. This is the exact gap that catches people off guard with older Delco housing stock, where a furnace might be original to a 1958 build or a system might have been swapped into ductwork it was never sized for.
What Pennsylvania’s Seller Disclosure form does and doesn’t guarantee
Pennsylvania requires sellers to complete a Seller’s Property Disclosure Statement, and it includes questions about the heating and cooling systems: age, known defects, and recent repairs. It feels like a safety net. It isn’t the one buyers think it is.
The disclosure law only obligates a seller to report defects they actually know about. If the seller never had the furnace’s heat exchanger inspected, never had the AC’s charge checked, or genuinely doesn’t know the compressor is on its last leg, they can answer “no known defects” in complete good faith. A seller who inherited the house, a landlord who never lived there, or an owner who simply never had issues come up can all sign a clean disclosure form on a system that’s one summer away from failing.
That’s the core problem with relying on disclosure plus a general home inspection as your only due diligence. Neither one is designed to catch a system that’s functioning today but mechanically compromised. You can inherit a failing furnace or AC that a seller disclosed honestly and a general inspector signed off on, and still be the one paying for the replacement six months after closing.
Frontline’s pre-purchase HVAC inspection checklist
A stand-alone pre-purchase HVAC inspection is built to answer the questions a general inspection can’t. Here’s what it actually covers:
- Refrigerant charge and pressures. We connect gauges to the AC system and compare actual operating pressures against manufacturer specs, not just confirm it blows cold air.
- Electrical amp draw. We test the compressor, condenser fan motor, and blower motor against their nameplate ratings to catch a motor that’s drawing too hard and nearing failure.
- Combustion and CO safety test. For gas furnaces, we run a combustion analysis and inspect the heat exchanger for cracks or corrosion, the single biggest safety item a general inspector cannot access.
- Duct static pressure. We measure whether the system is fighting against undersized or clogged ductwork, a common issue in homes where ducts were added decades after the original build.
- Serial-number age pull. We pull the actual manufacture date off the equipment nameplate instead of relying on what the seller remembers or what’s listed on the MLS. If you want to check this yourself before scheduling anything, our serial number age lookup guide walks through how to find and read it.
Once we know the real age and condition, we can give you a straight answer on whether you’re looking at a system with years of life left or one that’s a candidate for the repair-vs-replace conversation within the first year or two of ownership.
What it costs and when to schedule it
A stand-alone pre-purchase HVAC inspection is a separate line item from your general home inspection, and it’s priced differently because it involves actual diagnostic equipment, like gauges, a combustion analyzer, and an amp clamp, rather than a visual walkthrough. The right time to schedule it is during your home inspection contingency period, ideally right after the general inspection report comes back and before you decide whether to waive any contingencies tied to it. That gives you a real mechanical answer on the HVAC system while you still have leverage to negotiate a price reduction, request a pre-closing repair, or walk away.
Waiting until after closing to find out the AC needs a full recharge or the furnace needs a new heat exchanger means you’re paying out of pocket with no negotiating room left. If you’re selling, the same logic runs in reverse: a pre-listing HVAC inspection lets you either fix small issues before they show up in a buyer’s inspection or price the house accounting for a system that’s near end of life, which keeps the deal from blowing up at the eleventh hour.
Red flags to ask about before waiving a contingency
Before you sign away your right to inspect further, ask the seller or agent directly about these items. A clean answer doesn’t guarantee a clean system, but a vague or dodged answer is itself information:
- The actual age of the furnace and AC, confirmed by serial number, not listing copy
- Whether the system has had any service calls, refrigerant top-offs, or repairs in the last two years
- Whether the ductwork is original to the house or was added or modified later, especially in homes with additions or finished basements
- Whether there’s any sign of water damage near the furnace, which can point to a condensate or drain line issue that’s been managed rather than fixed
- Whether the system has ever been serviced by a licensed contractor, or only ever “looked at” by a handyman or the seller themselves
If the system is old enough to be near the end of its expected service life, it’s also worth asking what a full replacement would run, and whether current rebates or tax credits could offset that cost if you end up needing to replace it shortly after move-in. And if homeowners insurance comes up in conversation with your agent, it’s worth knowing upfront that most policies don’t cover HVAC failure from normal wear and age, only sudden covered perils, so a failing system found post-closing is almost always coming out of your pocket.
Schedule a pre-purchase or pre-listing HVAC inspection in Delaware County
Whether you’re under contract on a house in Delco and want a real mechanical answer before your contingency window closes, or you’re listing a house and want to head off a buyer’s inspection surprise, Frontline runs the full diagnostic checklist: refrigerant charge, amp draw, combustion and CO safety, duct static pressure, and a true age pull from the equipment serial number. You get a written report you can actually use at the negotiating table, not a checkbox that says the system turned on.
Contact Frontline to schedule a pre-purchase or pre-listing HVAC inspection before your closing date. We work across Delaware County and can usually get you an appointment within your contingency window.